亚洲欧美中文字幕影院,欧美成人激情免费一区,亚洲成AⅤ人在线观看无码,欧美日激情日韩精品嗯

免費注冊快速求購

當前位置：儀器網 > 產品中心 > 行業專用儀器>其它行業專用儀器>其它> 數顯式陶瓷吸水率測定儀技術參數榮計達TXS-II

返回產品中心>

舉報評價

數顯式陶瓷吸水率測定儀技術參數榮計達TXS-II

參考價	面議

參考價

面議

具體成交價以合同協議為準

公司名稱 上海榮計達實驗儀器有限公司
品牌
型號
所在地
廠商性質 生產廠家
更新時間 2021/3/5 13:20:47
訪問次數 384

在線詢價收藏產品點擊查看聯系電話

索取相關資料

促銷詳情

促銷時間：

特價說明：

促銷詳細：

2020年01月08日至 2020年02月08日

特價促銷

模內澆口分離自動化，降低對人的依賴度；傳統的塑膠模具開模后產品與澆口相連，需二道工序進行人工剪切分離，模內熱切模具將澆口分離提前至開模前，消除后續工序，有利于生產自動化，降低對人的依賴。

陶瓷吸水率測定儀按照Q/JYY0052003《CXK型陶瓷真空吸水率真空裝置》，符合GB/T3810.32006《陶瓷磚試驗方法第3部分：吸水率、顯氣孔率、表觀相對密度和容重的測定》、ISO10545-3:1995《陶瓷磚第3部分：吸水率、顯氣孔率、表觀相對密度和容重的測定》、TOCT1344982等試驗方法中真空法對試驗設備的要求。陶瓷吸水率測定儀采用不銹鋼真空室，真空度實現自動控制，給排水為手動控制，具有操作簡便、試驗準確等特點。該真空裝置適用于建筑衛生陶瓷及其它材料吸水率測定的試驗。

詳細信息在線詢價

陶瓷吸水率測定儀按照Q/JYY005—2003《CXK型陶瓷真空吸水率真空裝置》，符合GB/T3810.3—2006《陶瓷磚試驗方法—第3部分：吸水率、顯氣孔率、表觀相對密度和容重的測定》、ISO10545-3:1995《陶瓷磚—第3部分：吸水率、顯氣孔率、表觀相對密度和容重的測定》、TOCT13449—82等試驗方法中真空法對試驗設備的要求。陶瓷吸水率測定儀采用不銹鋼真空室，真空度實現自動控制，給排水為手動控制，具有操作簡便、試驗準確等特點。該真空裝置適用于建筑衛生陶瓷及其它材料吸水率測定的試驗。
The ceramic water absorption rate tester is in accordance with Q/JYY005-2003 "CXK type ceramic vacuum water absorption vacuum device", in line with GB/T3810.3-2006 "Ceramic tile test method-Part 3: Water absorption, apparent porosity, apparent relative Determination of Density and Bulk Density", ISO10545-3:1995 "Ceramic Tiles—Part 3: Determination of Water Absorption, Apparent Porosity, Apparent Relative Density and Bulk Density", TOCT13449-82 and other test methods in the vacuum method on the test equipment Claim. The ceramic water absorption rate tester adopts a stainless steel vacuum chamber, the vacuum degree is automatically controlled, and the water supply and drainage is manually controlled. It has the characteristics of simple operation and accurate testing. The vacuum device is suitable for testing the water absorption rate of building sanitary ceramics and other materials.

陶瓷吸水率測定儀技術參數：
◆系統真空度能在≥0.095MPa范圍連續可調。
◆系統達到10kPa真空度所用的抽氣時間不大于10min。
◆試樣的大尺寸為200×200（mm）
◆設備外形尺寸： 800×750×1200（mm）
Technical parameters of ceramic water absorption tester:
◆The vacuum degree of the system can be continuously adjusted in the range of ≥0.095MPa.
◆The pumping time for the system to reach a vacuum of 10kPa is not more than 10min.
◆The large size of the sample is 200×200 (mm)
◆Equipment dimensions: 800×750×1200 (mm)

陶瓷吸水率測定儀試驗方法：
◆真空裝置由真空系統，給排水系統，真空度自動控制系統，控制按鈕及機箱組成。
◆真空系統包括真空壓力控制表、真空容器、真空泵、電磁真空閥、壓力變送器、進氣閥及管道組成。
◆給排水系統由進水閥、排水閥、儲水器及水管組成。
◆真空度控制系統由泵體真空壓力控制表、真空泵、壓力變送器、主電源開關及電磁閥組成。
◆關閉注水閥以及設備左下方的排水閥（真空容器排水閥，‚真空泵儲水器排水閥）。
◆打開真空容器上蓋，將支架放置容器內，將稱重好后的試樣放在支架上，注意要確保試樣表面無油污和灰塵。
◆向容器中注入蒸餾水，水位以超過試樣125px為宜，蓋上容器蓋，緊固螺絲，確保密封*。
◆打開設備側門向真空泵儲水器倒入蒸餾水，水量為儲水器容積的90%。
◆做好上述事項，按紅色按鈕啟動真空泵，待壓力達到要求后，按綠色按鈕開始計時。
◆試驗時間達到后，關閉電源，打開注水閥，待壓力表指針歸零，打開上蓋，取出試樣擦干稱重記錄數據。
Test method of ceramic water absorption tester:
◆The vacuum device is composed of vacuum system, water supply and drainage system, vacuum degree automatic control system, control buttons and cabinet.
◆The vacuum system includes a vacuum pressure control gauge, a vacuum container, a vacuum pump, an electromagnetic vacuum valve, a pressure transmitter, an air inlet valve and a pipeline.
◆The water supply and drainage system consists of water inlet valve, drain valve, water reservoir and water pipe.
◆Vacuum degree control system consists of pump body vacuum pressure control gauge, vacuum pump, pressure transmitter, main power switch and solenoid valve.
◆Close the water injection valve and the drain valve (vacuum container drain valve, ‚vacuum pump reservoir drain valve) at the bottom left of the equipment.
◆Open the upper cover of the vacuum container, place the holder in the container, and place the weighed sample on the holder. Take care to ensure that the sample surface is free of oil and dust.
◆Pour distilled water into the container. The water level should be more than 125px of the sample. Close the container lid and tighten the screws to ensure a complete seal.
◆Open the side door of the equipment and pour distilled water into the vacuum pump reservoir. The water volume is 90% of the volume of the reservoir.
◆After completing the above items, press the red button to start the vacuum pump, and when the pressure reaches the requirement, press the green button to start timing.
◆After the test time is up, turn off the power, open the water injection valve, wait for the pointer of the pressure gauge to return to zero, open the upper cover, take out the sample, wipe dry, weigh and record the data.

陶瓷吸水率測定儀注意事項：
◆真空容器內保持干凈清潔，不有積水和灰塵。
◆定期檢查真空泵，注意真空泵的使用說明。
Note for ceramic water absorption tester:
◆Keep the vacuum container clean and free of water and dust.
◆Check the vacuum pump regularly and pay attention to the instructions for use of the vacuum pump.